FACP IQ8Control M
Description
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet via a standard RJ45 Ethernet jack using the shield.
The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). You can access the on-board SD card slot using the SD library which is included in the current Arduino build.
The latest revision of the shield also includes a reset controller, to ensure that the W5100 Ethernet module is properly reset on power-up. Previous revisions of the shield were not compatible with the Mega and need to be manually reset after power-up. The reset button on the shield resets both the W5100 and the Arduino board.
Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 11, 12, and 13 on the Duemilanove and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output or the SPI interface won't work.
The IQ8Control M as an efficient fire alarm control panel (FACP) for the property supervision of mid-sized to large objects, facilitates simultaneous detection, control and alarm signaling both on the analog ring as well as on the spur.
The loop operation type of the panel (powered-loop or non-powered-loop) can be selected via a jumper located on the power supply card.
Depending on which loop operation type has been selected, the corresponding analog module/modules should be used.
Part No.: 808004 Approval: VdS, CNBOP, BOSEC
Features
Max. five micromodules, with peripheral module Part No. 772477, up to five esserbus analog loop modules (system supports up to 635 digital loop addresses in total)
Max. seven micromodules, with extension module Part No. 772476, up to seven esserbus analog loop modules (system supports up to 889 digital loop addresses in total)
Short circuit and open circuit tolerant loop operation
Loop installation with I-Y(ST)Y 0.8 mm cable for a maximum length of 3.5 km
Up to 127 esserbus devices (fire detectors and/or manual call points)/detector zones per loop
Up to 32 esserbus transponders per loop/operation of wireless components (see chapter 10)
Operation types TM and PM as per DIN VDE 0833 - 2 to avoid unwanted alarms being triggered
Fire brigade operating panel and transmission interface on the peripheral module
Three common relays, freely programmable, monitored, floating for up to 30 V DC/1A (on the peripheral module)
TTY or RS 485 or RS 232 interface
Integration in the short circuit and open circuit resistant essernet network with up to 31 fire detection panels depends on transmission rate
Connection to graphical supervisor WINMAG via serial essernet interface (SEI)
Operating panel with alphanumerical display
Large display with 8 rows with 40 characters. As follows rated - four rows with 40 characters for the status information (first and last message), and the other four rows with 40 characters are used for system information e.g. “Sounders Off”
Event memory for up to 10,000 events
All Systems 8000 micromodules are compatible
Printer interface for internal printer
Two batteries with monitoring circuit
Monitored input for external power supply unit
Additional features for powered loop
Max. 6 analog powered loops and expandable up to 127 loop devices (per loop) in mixed mode / loop powered and non-loop powered (system supports up to 762 digital loop addresses in total)
esserbus PLus (Powered Loop) supplied, synchronously controlled, acoustic alarm signaling devices as per DIN EN 54 - 3 with alarm tone as per DIN 33404
Up to 48 powered loop base sounders (series 9200) per loop
Up to 32 powered loop IQ8Alarm per loop
Up to 48 IQ8Quad with alarm device per loop